2019.03.01 00:52

가속, 자이로, 온도, 압감지, 마그넷 센서

LSM6DSL, LIS2MDL, LPS22HB

소스와 통신하는 부분을 ST에서 제공하는 프로그램에서 발췌했더니 비효율적으로 되어있습니다.

데이터시트를 보고 최적화와 함께 함수들을 만들어 써야합니다. 


void main(void)

{

ACCGyroAxis_TypeDef ACCAxis, GyroAxis;

MagnetAxis_TypeDef MagnetAxis;

float fPress, ftemperature;

float fBatt;

uint16_t Batt_Percent;


LSM6DSL_ACCGyroInit();

LIS2MDL_MagnetInit();

LPS22HB_TempPreInit();


LSM6DSL_ACCGyroEnable();

LIS2MDL_MagnetEnable();

LPS22HB_TempPreEnable();


LSM6DSL_ACCGyroSetting();

LIS2MDL_MagnetSetting();

while(1)

{

MeasurementSensorData(5, &ACCAxis, &GyroAxis, &MagnetAxis, &fPress, &ftemperature, &fBatt, &Batt_Percent);

}

}



/* Private typedef -----------------------------------------------------------*/

/* Private define ------------------------------------------------------------*/

#define LSM6DSL_ACC_SENSITIVITY_FOR_FS_2G   0.061  /**< Sensitivity value for 2 g full scale [mg/LSB] */

#define LSM6DSL_ACC_SENSITIVITY_FOR_FS_4G   0.122  /**< Sensitivity value for 4 g full scale [mg/LSB] */

#define LSM6DSL_ACC_SENSITIVITY_FOR_FS_8G   0.244  /**< Sensitivity value for 8 g full scale [mg/LSB] */

#define LSM6DSL_ACC_SENSITIVITY_FOR_FS_16G  0.488  /**< Sensitivity value for 16 g full scale [mg/LSB] */


#define LSM6DSL_GYRO_SENSITIVITY_FOR_FS_125DPS   04.375  /**< Sensitivity value for 125 dps full scale [mdps/LSB] */

#define LSM6DSL_GYRO_SENSITIVITY_FOR_FS_245DPS   08.750  /**< Sensitivity value for 245 dps full scale [mdps/LSB] */

#define LSM6DSL_GYRO_SENSITIVITY_FOR_FS_500DPS   17.500  /**< Sensitivity value for 500 dps full scale [mdps/LSB] */

#define LSM6DSL_GYRO_SENSITIVITY_FOR_FS_1000DPS  35.000  /**< Sensitivity value for 1000 dps full scale [mdps/LSB] */

#define LSM6DSL_GYRO_SENSITIVITY_FOR_FS_2000DPS  70.000  /**< Sensitivity value for 2000 dps full scale [mdps/LSB] */


#define LSM6DSL_ACC_SENSITIVITY LSM6DSL_ACC_SENSITIVITY_FOR_FS_2G

#define LSM6DSL_GYRO_SENSITIVITY LSM6DSL_GYRO_SENSITIVITY_FOR_FS_2000DPS


typedef enum {

 eModeACC = 0,  

 eModeGyro,  

} eModeACCGyro_TypeDef;


typedef struct {

int32_t ACCGyro_X;

int32_t ACCGyro_Y;

int32_t ACCGyro_Z;

}ACCGyroAxis_TypeDef;


//#define LSM6DSL_RESERVED 0x00

#define LSM6DSL_FUNC_CFG_ACCESS 0x01 //Embedded functions

//#define LSM6DSL_RESERVED 0x02

//#define LSM6DSL_RESERVED 0x03

#define LSM6DSL_SENSOR_SYNC_TIME_FRAME 0x04 //r/w

#define LSM6DSL_SENSOR_SYNC_RES_RATIO 0x05 //r/w

#define LSM6DSL_FIFO_CTRL1 0x06 //r/w

#define LSM6DSL_FIFO_CTRL2 0x07 //r/w

#define LSM6DSL_FIFO_CTRL3 0x08 //r/w

#define LSM6DSL_FIFO_CTRL4 0x09 //r/w

#define LSM6DSL_FIFO_CTRL5 0x0A //r/w

#define LSM6DSL_DRDY_PULSE_CFG_G 0x0B //r/w

//#define LSM6DSL_RESERVED 0x0C

#define LSM6DSL_INT1_CTRL 0x0D //r/w INT1 pin control

#define LSM6DSL_INT2_CTRL 0x0E //r/w INT2 pin control

#define LSM6DSL_WHO_AM_I 0x0F //r Who I am ID

#define LSM6DSL_CTRL1_XL 0x10 //r/w

#define LSM6DSL_CTRL2_G 0x11 //r/w

#define LSM6DSL_CTRL3_C 0x12 //r/w

#define LSM6DSL_CTRL4_C 0x13 //r/w

#define LSM6DSL_CTRL5_C 0x14 //r/w

#define LSM6DSL_CTRL6_C 0x15 //r/w

#define LSM6DSL_CTRL7_G 0x16 //r/w

#define LSM6DSL_CTRL8_XL 0x17 //r/w

#define LSM6DSL_CTRL9_XL 0x18 //r/w

#define LSM6DSL_CTRL10_C 0x19 //r/w

#define LSM6DSL_MASTER_CONFIG 0x1A //r/w

#define LSM6DSL_WAKE_UP_SRC 0x1B //r

#define LSM6DSL_TAP_SRC 0x1C //r  Interrupt registers

#define LSM6DSL_D6D_SRC 0x1D //r  

#define LSM6DSL_STATUS_REG 0x1E //r  

//#define LSM6DSL_RESERVED 0x1F

#define LSM6DSL_OUT_TEMP_L 0x20 //r   Temperature output

#define LSM6DSL_OUT_TEMP_H 0x21 //r   data registers

#define LSM6DSL_OUTX_L_G 0x22 //r   GYRO

#define LSM6DSL_OUTX_H_G 0x23 //r  

#define LSM6DSL_OUTY_L_G 0x24 //r  

#define LSM6DSL_OUTY_H_G 0x25 //r  

#define LSM6DSL_OUTZ_L_G 0x26 //r  

#define LSM6DSL_OUTZ_H_G 0x27 //r  

#define LSM6DSL_OUTX_L_XL 0x28 //r   ACC

#define LSM6DSL_OUTX_H_XL 0x29 //r  

#define LSM6DSL_OUTY_L_XL 0x2A //r  

#define LSM6DSL_OUTY_H_XL 0x2B //r  

#define LSM6DSL_OUTZ_L_XL 0x2C //r  

#define LSM6DSL_OUTZ_H_XL 0x2D //r  

#define LSM6DSL_SENSORHUB1_REG 0x2E //r  

#define LSM6DSL_SENSORHUB2_REG 0x2F //r  

#define LSM6DSL_SENSORHUB3_REG 0x30 //r  

#define LSM6DSL_SENSORHUB4_REG 0x31 //r  

#define LSM6DSL_SENSORHUB5_REG 0x32 //r  

#define LSM6DSL_SENSORHUB6_REG 0x33 //r  

#define LSM6DSL_SENSORHUB7_REG 0x34 //r  

#define LSM6DSL_SENSORHUB8_REG 0x35 //r  

#define LSM6DSL_SENSORHUB9_REG 0x36 //r  

#define LSM6DSL_SENSORHUB10_REG 0x37 //r  

#define LSM6DSL_SENSORHUB11_REG 0x38 //r  

#define LSM6DSL_SENSORHUB12_REG 0x39 //r  

#define LSM6DSL_FIFO_STATUS1 0x3A //r  

#define LSM6DSL_FIFO_STATUS2 0x3B //r  

#define LSM6DSL_FIFO_STATUS3 0x3C //r  

#define LSM6DSL_FIFO_STATUS4 0x3D //r  

#define LSM6DSL_FIFO_DATA_OUT_L 0x3E //r   FIFO data output

#define LSM6DSL_FIFO_DATA_OUT_H 0x3F //r  

#define LSM6DSL_TIMESTAMP0_REG 0x40 //r  

#define LSM6DSL_TIMESTAMP1_REG 0x41 //r  

#define LSM6DSL_TIMESTAMP2_REG 0x42 //r/w  

//#define LSM6DSL_RESERVED 0x43 ~ 0x48

#define LSM6DSL_STEP_TIMESTAMP_L 0x49 //r   Step counter

#define LSM6DSL_STEP_TIMESTAMP_H 0x4A //r   timestamp registers

#define LSM6DSL_STEP_COUNTER_L 0x4B //r   Step counte0xoutput

#define LSM6DSL_STEP_COUNTER_H 0x4C //r   registers

#define LSM6DSL_SENSORHUB13_REG 0x4D //r  

#define LSM6DSL_SENSORHUB14_REG 0x4E //r  

#define LSM6DSL_SENSORHUB15_REG 0x4F //r  

#define LSM6DSL_SENSORHUB16_REG 0x50 //r  

#define LSM6DSL_SENSORHUB17_REG 0x51 //r  

#define LSM6DSL_SENSORHUB18_REG 0x52 //r  

#define LSM6DSL_FUNC_SRC1 0x53 //r  

#define LSM6DSL_FUNC_SRC2 0x54 //r  

#define LSM6DSL_WRIST_TILT_IA 0x55 //r   Interrupt register

//#define LSM6DSL_RESERVED - 56-57 - 

#define LSM6DSL_TAP_CFG 0x58 //r/w  

#define LSM6DSL_TAP_THS_6D 0x59 //r/w  

#define LSM6DSL_INT_DUR2 0x5A //r/w  

#define LSM6DSL_WAKE_UP_THS 0x5B //r/w  

#define LSM6DSL_WAKE_UP_DU0x0x5C //r/w  

#define LSM6DSL_FREE_FALL 0x5D //r/w  

#define LSM6DSL_MD1_CFG 0x5E //r/w  

#define LSM6DSL_MD2_CFG 0x5F //r/w  

#define LSM6DSL_MASTER_CMD_CODE 0x60 //r/w  

#define LSM6DSL_SENS_SYNC_SPI_ERROR_CODE 0x61 //r/w 

//#define LSM6DSL_RESERVED - 62-65 - Reserved

#define LSM6DSL_OUT_MAG_RAW_X_L 0x66 //r  

#define LSM6DSL_OUT_MAG_RAW_X_H 0x67 //r  

#define LSM6DSL_OUT_MAG_RAW_Y_L 0x68 //r  

#define LSM6DSL_OUT_MAG_RAW_Y_H 0x69 //r  

#define LSM6DSL_OUT_MAG_RAW_Z_L 0x6A //r  

#define LSM6DSL_OUT_MAG_RAW_Z_H 0x6B //r  

//#define LSM6DSL_RESERVED - 6C-72 - 

#define LSM6DSL_X_OFS_US0x0x73 //r/w  

#define LSM6DSL_Y_OFS_US0x0x74 //r/w  

#define LSM6DSL_Z_OFS_US0x0x75 //r/w  

//#define LSM6DSL_RESERVED - 76-7F -



/* Private macro ------------------------------------------------------------*/

/* Private variables ---------------------------------------------------------*/

/* Private function prototypes ------------------------------------------------*/

/* Private functions ---------------------------------------------------------*/

extern void UART1_printf(const char *fmt,...);

ACCGyroAxis_TypeDef gstACCAxis;

ACCGyroAxis_TypeDef gstGyroAxis;



/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LSM6DSL_ACCGyroInit(void)

{

uint8_t Data[10];


Data[0] = 0x0C;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL3_C, Data, 1);

Data[0] = 0x00;

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_WHO_AM_I, Data, 1);

Data[0] = 0x6A;

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL3_C, Data, 1);

Data[0] = 0x0C;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL3_C, Data, 1);

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL3_C, Data, 1);

Data[0] = 0x4C;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL3_C, Data, 1);

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_FIFO_CTRL5, Data, 1);

Data[0] = 0x00;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_FIFO_CTRL5, Data, 1);

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL1_XL, Data, 1);

Data[0] = 0x00;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL1_XL, Data, 1);

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL1_XL, Data, 1);

Data[0] = 0x00;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL1_XL, Data, 1);

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL4_C, Data, 1);

Data[0] = 0x04;

SPI2_1Wire_Write(CS_LSM6DSL,LSM6DSL_CTRL4_C, Data, 1);

Data[0] = 0x00;

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_WHO_AM_I, Data, 1);

Data[0] = 0x6A;

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL3_C, Data, 1);

Data[0] = 0x4C;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL3_C, Data, 1);

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL3_C, Data, 1);

Data[0] = 0x4C;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL3_C, Data, 1);

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_FIFO_CTRL5, Data, 1);

Data[0] = 0x00;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_FIFO_CTRL5, Data, 1);

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL2_G, Data, 1);

Data[0] = 0x0C;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL2_G, Data, 1);

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL2_G, Data, 1);

Data[0] = 0x0C;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL2_G, Data, 1);

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL4_C, Data, 1);

Data[0] = 0x04;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL4_C, Data, 1);

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

<- \ ACC + / ACC-

Side

Right - Left +

*******************************************************************************/

void LSM6DSL_ACCGyroEnable(void)

{

uint8_t Data[10], ACCGyroLoop;

Data[0] = 0x01;

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL1_XL, Data, 1);

Data[0] = 0x40;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL1_XL, Data, 1);

Data[0] = 0x0A;

SPI2_1Wire_Read(CS_LSM6DSL, LSM6DSL_CTRL2_G, Data, 1);

Data[0] = 0x4C;

SPI2_1Wire_Write(CS_LSM6DSL, LSM6DSL_CTRL2_G, Data, 1);

delay_ms(100);

ACCGyroAxis_TypeDef ACCAxis, GyroAxis;

LSM6DSL_ACCGyroGet(&gstACCAxis, &gstGyroAxis);

for(ACCGyroLoop = 0; ACCGyroLoop < 10; ACCGyroLoop++){

LSM6DSL_ACCGyroGet(&ACCAxis, &GyroAxis);

gstACCAxis.ACCGyro_X = (gstACCAxis.ACCGyro_X + ACCAxis.ACCGyro_X)/2;

gstACCAxis.ACCGyro_Y = (gstACCAxis.ACCGyro_Y + ACCAxis.ACCGyro_Y)/2;

gstACCAxis.ACCGyro_Z = (gstACCAxis.ACCGyro_Z + ACCAxis.ACCGyro_Z)/2;

gstGyroAxis.ACCGyro_X = (gstGyroAxis.ACCGyro_X + GyroAxis.ACCGyro_X)/2;

gstGyroAxis.ACCGyro_Y = (gstGyroAxis.ACCGyro_Y + GyroAxis.ACCGyro_Y)/2;

gstGyroAxis.ACCGyro_Z = (gstGyroAxis.ACCGyro_Z + GyroAxis.ACCGyro_Z)/2;

delay_ms(1);

}

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LSM6DSL_ACCGyroSetting(void)

{

uint8_t Data[10];


//ODR 6.6kHz   

Data[0] = 0x0A;

SPI2_1Wire_Read(CS_LSM6DSL, 0x10, Data, 1);

Data[0] = 0xA0;

SPI2_1Wire_Write(CS_LSM6DSL, 0x10, Data, 1);

//FS 4g

Data[0] = 0xA0;

SPI2_1Wire_Read(CS_LSM6DSL, 0x10, Data, 1);

Data[0] = 0xA8;

SPI2_1Wire_Write(CS_LSM6DSL, 0x10, Data, 1);

//ODR/2 low pass filtered sent to composite filter

Data[0] = 0xA8;

SPI2_1Wire_Read(CS_LSM6DSL, 0x17, Data, 1);

Data[0] &= ~0x80;//LSM6DSL_ACC_GYRO_IN_COMP_MASK;

  Data[0] |= 0x00;//LSM6DSL_ACC_GYRO_IN_ODR_DIV_2;

SPI2_1Wire_Write(CS_LSM6DSL, 0x17, Data, 1);

//Enable LPF2 filter in composite filter block

Data[0] = 0x60;

SPI2_1Wire_Read(CS_LSM6DSL, 0x17, Data, 1);

Data[0] &= ~0x80;//LSM6DSL_ACC_GYRO_LPF2_XL_MASK;

  Data[0] |= 0x80;//LSM6DSL_ACC_GYRO_LPF2_XL_ENABLE;

SPI2_1Wire_Write(CS_LSM6DSL, 0x17, Data, 1);

//Low pass filter @ ODR/400

Data[0] = 0xE0;

SPI2_1Wire_Read(CS_LSM6DSL, 0x17, Data, 1);

Data[0] &= ~0x60;//LSM6DSL_ACC_GYRO_HPCF_XL_MASK;

  Data[0] |= 0x60;//LSM6DSL_ACC_GYRO_HPCF_XL_DIV400;

SPI2_1Wire_Write(CS_LSM6DSL, 0x17, Data, 1);

//ACC Read

Data[0] = 0x00;

SPI2_1Wire_Read(CS_LSM6DSL, 0x10, Data, 1);

//Set LSB to 0 >> Analog filter 1500Hz

Data[0] &= 0xFE;

SPI2_1Wire_Write(CS_LSM6DSL, 0x10, Data, 1);

// Initialize settings for 6-axis MEMS Gyroscope 

// FS 2000dps */

// ODR 416Hz */

// LPF1 FTYPE set to 10b 

Data[0] = 0xA8;

SPI2_1Wire_Read(CS_LSM6DSL, 0x15, Data, 1);

Data[0] &= ~0x03;//LSM6DSL_ACC_GYRO_FTYPE_MASK   

  Data[0] |= 0x01;//LSM6DSL_ACC_GYRO_LP_G_NARROW 

SPI2_1Wire_Write(CS_LSM6DSL, 0x15, Data, 1);

//Gyroscope settings: full scale 2000dps, ODR 416Hz

Data[0] = 0x6C;

SPI2_1Wire_Write(CS_LSM6DSL, 0x11, Data, 1);

}

/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LSM6DSL_ACCGyro(uint8_t *pRawdata, ACCGyroAxis_TypeDef *ACCGyroAxis, eModeACCGyro_TypeDef chMode)

{

short int ACCGyroTemp;

if(chMode == eModeACC){

ACCGyroTemp = ((((uint16_t)pRawdata[1]) << 8) + (uint16_t)pRawdata[0]);

ACCGyroAxis->ACCGyro_X = (ACCGyroTemp * LSM6DSL_ACC_SENSITIVITY);

ACCGyroTemp = ((((uint16_t)pRawdata[3]) << 8) + (uint16_t)pRawdata[2]);

ACCGyroAxis->ACCGyro_Y = (ACCGyroTemp * LSM6DSL_ACC_SENSITIVITY);

ACCGyroTemp = ((((uint16_t)pRawdata[5]) << 8) + (uint16_t)pRawdata[4]);

ACCGyroAxis->ACCGyro_Z = (ACCGyroTemp * LSM6DSL_ACC_SENSITIVITY);

}

else if(chMode == eModeGyro){

ACCGyroTemp = ((((uint16_t)pRawdata[1]) << 8) + (uint16_t)pRawdata[0]);

ACCGyroAxis->ACCGyro_X = (ACCGyroTemp * LSM6DSL_GYRO_SENSITIVITY);

ACCGyroTemp = ((((uint16_t)pRawdata[3]) << 8) + (uint16_t)pRawdata[2]);

ACCGyroAxis->ACCGyro_Y = (ACCGyroTemp * LSM6DSL_GYRO_SENSITIVITY);

ACCGyroTemp = ((((uint16_t)pRawdata[5]) << 8) + (uint16_t)pRawdata[4]);

ACCGyroAxis->ACCGyro_Z = (ACCGyroTemp * LSM6DSL_GYRO_SENSITIVITY);

}

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LSM6DSL_RawData(uint8_t *pAddr, uint8_t *pRawData, uint8_t chLen)

{

uint8_t SpiLoop;

for(SpiLoop = 0; SpiLoop < chLen; SpiLoop++){

// UART1_printf("%02X, %02X, %02X \r\n", CS_LSM6DSL, pAddr[SpiLoop], pRawData[SpiLoop]);

SPI2_1Wire_Read(CS_LSM6DSL, pAddr[SpiLoop], &pRawData[SpiLoop], 1 );

}

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LSM6DSL_ACCGyroGet(ACCGyroAxis_TypeDef *ACCAxis, ACCGyroAxis_TypeDef *GyroAxis)

{

const uint8_t Data_ACCGyro[15] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xD1, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0A, 0xFE};

uint8_t Addr_ACCGyro[15] = \

{LSM6DSL_OUTX_L_XL, LSM6DSL_OUTX_H_XL, LSM6DSL_OUTY_L_XL, LSM6DSL_OUTY_H_XL, LSM6DSL_OUTZ_L_XL, LSM6DSL_OUTZ_H_XL\

, LSM6DSL_CTRL1_XL,\

LSM6DSL_OUTX_L_G, LSM6DSL_OUTX_H_G, LSM6DSL_OUTY_L_G, LSM6DSL_OUTY_H_G, LSM6DSL_OUTZ_L_G, LSM6DSL_OUTZ_H_G\

, LSM6DSL_CTRL2_G, LSM6DSL_CTRL2_G};

uint8_t Data[15] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xD1, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0A, 0xFE};

uint8_t pData[6];


memcpy(Data, Data_ACCGyro, 15);

LSM6DSL_RawData(Addr_ACCGyro, Data, 15);//0~5, 7~12

memcpy(pData, Data, 6);

LSM6DSL_ACCGyro(pData, ACCAxis, eModeACC);

memcpy(pData, Data+7, 6);

LSM6DSL_ACCGyro(pData, GyroAxis, eModeGyro);

}


/* Private typedef -----------------------------------------------------------*/

/* Private define ------------------------------------------------------------*/

typedef struct {

int32_t Mag_X;

int32_t Mag_Y;

int32_t Mag_Z;

}MagnetAxis_TypeDef;


//#define LIS2MDL_Reserved 00 - 44 Reserved

#define LIS2MDL_OFFSET_X_REG_L 0x45 //r/w  Hard-iron registers

#define LIS2MDL_OFFSET_X_REG_H 0x46 //r/w 

#define LIS2MDL_OFFSET_Y_REG_L 0x47 //r/w 

#define LIS2MDL_OFFSET_Y_REG_H 0x48 //r/w 

#define LIS2MDL_OFFSET_Z_REG_L 0x49 //r/w 

#define LIS2MDL_OFFSET_Z_REG_H 0x4A //r/w 

//#define LIS2MDL_RESERVED 4B-4C Reserved

#define LIS2MDL_WHO_AM_I 0x4F //r 

//#define LIS2MDL_RESERVED 50-5F Reserved

#define LIS2MDL_CFG_REG_A 0x60 //r/w  Configuration

#define LIS2MDL_CFG_REG_B 0x61 //r/w 

#define LIS2MDL_CFG_REG_C 0x62 //r/w 

#define LIS2MDL_INT_CRTL_REG 0x63 //r/w  configuration registers

#define LIS2MDL_INT_SOURCE_REG 0x64 //r

#define LIS2MDL_INT_THS_L_REG 0x65 //r/w 

#define LIS2MDL_INT_THS_H_REG 0x66 //r/w 

#define LIS2MDL_STATUS_REG 0x67 //r

#define LIS2MDL_OUTX_L_REG 0x68 //r  Output registers

#define LIS2MDL_OUTX_H_REG 0x69 //r 

#define LIS2MDL_OUTY_L_REG 0x6A //r 

#define LIS2MDL_OUTY_H_REG 0x6B //r 

#define LIS2MDL_OUTZ_L_REG 0x6C //r 

#define LIS2MDL_OUTZ_H_REG 0x6D //r 

#define LIS2MDL_TEMP_OUT_L_REG 0x6E //r  Temperature sensor

#define LIS2MDL_TEMP_OUT_H_REG 0x6F //r 


/* Private macro ------------------------------------------------------------*/

/* Private variables ---------------------------------------------------------*/

/* Private function prototypes ------------------------------------------------*/

/* Private functions ---------------------------------------------------------*/

extern void UART1_printf(const char *fmt,...);

MagnetAxis_TypeDef gStMagnetAxis;


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LIS2MDL_MagnetInit(void)

{

uint8_t Data[10];


Data[0] = 0x00;

SPI2_1Wire_Read(CS_LIS2MDL, LIS2MDL_WHO_AM_I, Data, 1);

Data[0] = 0x40;

SPI2_1Wire_Read(CS_LIS2MDL, LIS2MDL_CFG_REG_A, Data, 1);//reboot memory content

Data[0] = 0x0F;

SPI2_1Wire_Write(CS_LIS2MDL, LIS2MDL_CFG_REG_A, Data, 1);//Output data rate configuration - 50Hz

SPI2_1Wire_Read(CS_LIS2MDL, LIS2MDL_CFG_REG_C, Data, 1);

Data[0] = 0x10;

SPI2_1Wire_Write(CS_LIS2MDL, LIS2MDL_CFG_REG_C, Data, 1);// reading of incorrect data is avoided when the user reads asynchronously

SPI2_1Wire_Read(CS_LIS2MDL, LIS2MDL_CFG_REG_A, Data, 1);

Data[0] = 0x0F;

SPI2_1Wire_Write(CS_LIS2MDL, LIS2MDL_CFG_REG_A, Data, 1);

SPI2_1Wire_Read(CS_LIS2MDL, LIS2MDL_CFG_REG_C, Data, 1);

Data[0] = 0x10;

SPI2_1Wire_Write(CS_LIS2MDL, LIS2MDL_CFG_REG_C, Data, 1);

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

1. Write CFG_REG_A = 80h // Enable temperature compensation

//Mag = 10 Hz (high-resolution and continuous mode)

2. Write CFG_REG_C = 01h // Mag data-ready interrupt enable

*******************************************************************************/

void LIS2MDL_MagnetEnable(void)

{

uint8_t Data[10];


Data[0] = 0x0A;

SPI2_1Wire_Read(CS_LIS2MDL, LIS2MDL_CFG_REG_A, Data, 1);

Data[0] = 0x0C;

SPI2_1Wire_Write(CS_LIS2MDL, LIS2MDL_CFG_REG_A, Data, 1);//100Hz

}



/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

Initialize settings for Magnetometer settings 

(By default after reset is in in idle mode) 

*******************************************************************************/

void LIS2MDL_MagnetSetting(void)

{

uint8_t Data[10];


Data[0] = 0x8C;

SPI2_1Wire_Write(CS_LIS2MDL, LIS2MDL_CFG_REG_A, Data, 1);

Data[0] = 0x02;

SPI2_1Wire_Write(CS_LIS2MDL, LIS2MDL_CFG_REG_B, Data, 1);

}

/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LIS2MDL_Magnet(uint8_t *pRawdata, MagnetAxis_TypeDef *MagnetAxis, float fSensitivity)

{

short int MagnetTemp;

MagnetTemp = (((uint16_t)pRawdata[1]) << 8) + (uint16_t)pRawdata[0];

MagnetAxis->Mag_X = (MagnetTemp * fSensitivity);

MagnetTemp = (((uint16_t)pRawdata[3]) << 8) + (uint16_t)pRawdata[2];

MagnetAxis->Mag_Y  = (MagnetTemp * fSensitivity);

MagnetTemp = (((uint16_t)pRawdata[5]) << 8) + (uint16_t)pRawdata[4];

MagnetAxis->Mag_Z  = (MagnetTemp * fSensitivity);

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LIS2MDL_RawData(uint8_t *pAddr, uint8_t *pRawData, uint8_t chLen)

{

uint8_t SpiLoop;

for(SpiLoop = 0; SpiLoop < chLen; SpiLoop++){

// UART1_printf("%02X, %02X, %02X \r\n", CS_LIS2MDL, pAddr[SpiLoop], pRawData[SpiLoop]);

SPI2_1Wire_Read(CS_LIS2MDL, pAddr[SpiLoop], &pRawData[SpiLoop], 1 );

}

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LIS2MDL_MagnetGet(MagnetAxis_TypeDef *MagnetAxis)

{

uint8_t Addr_Magnet[6] = {0x68, 0x69, 0x6A, 0x6B, 0x6C, 0x6D};

uint8_t Data[6] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00};


int16_t *pRawData;

float Sensitivity = 1.5f;

LIS2MDL_RawData(Addr_Magnet, Data, 6);

LIS2MDL_Magnet(Data, MagnetAxis, Sensitivity);

}


/* Private typedef -----------------------------------------------------------*/

/* Private define ------------------------------------------------------------*/

//#define LPS22HB_Reserved 0x00 - 0A - Reserved

#define LPS22HB_INTERRUPT_CFG 0x0B //r/w Interrupt register

#define LPS22HB_THS_P_L 0x0C //r/w threshold registers

#define LPS22HB_THS_P_H 0x0D //r/w

//#define LPS22HB_Reserved 0E - Reserved

#define LPS22HB_WHO_AM_I 0x0F //r Who am I

#define LPS22HB_CTRL_REG1 0x10 //r/w

#define LPS22HB_CTRL_REG2 0x11 //r/w Control registers

#define LPS22HB_CTRL_REG3 0x12 //r/w

//#define LPS22HB_Reserved 13 - Reserved

#define LPS22HB_FIFO_CTRL 0x14 //r/w FIFO configuration register

#define LPS22HB_REF_P_XL 0x15 //r/w

#define LPS22HB_REF_P_L 0x16 //r/w Reference pressure registers

#define LPS22HB_REF_P_H 0x17 //r/w

#define LPS22HB_RPDS_L 0x18 //r/w offset registers

#define LPS22HB_RPDS_H 0x19 //r/w

#define LPS22HB_RES_CONF 0x1A //r/w Resolution register

//#define LPS22HB_Reserved 1B - 24 - Reserved

#define LPS22HB_INT_SOURCE 0x25 //r Interrupt register

#define LPS22HB_FIFO_STATUS 0x26 //r FIFO status register

#define LPS22HB_STATUS 0x27 //r Status register

#define LPS22HB_PRESS_OUT_XL 0x28 //r

#define LPS22HB_PRESS_OUT_L 0x29 //r Pressure output registers

#define LPS22HB_PRESS_OUT_H 0x2A //r

#define LPS22HB_TEMP_OUT_L 0x2B //r Temperature output registers

#define LPS22HB_TEMP_OUT_H 0x2C //r

//#define LPS22HB_Reserved 2D - 32 - Reserved

#define LPS22HB_LPFP_RES 0x33 //r Filte0xreset register


/* Private macro ------------------------------------------------------------*/

/* Private variables ---------------------------------------------------------*/

/* Private function prototypes ------------------------------------------------*/

/* Private functions ---------------------------------------------------------*/


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LPS22HB_TempPreInit(void)

{

uint8_t Data[10];


Data[0] = 0x01;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG2, Data, 1);

Data[0] = 0xFC;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG2, Data, 1);

Data[0] = 0x01;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

Data[0] = 0x01;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

Data[0] = 0x00;

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_WHO_AM_I, Data, 1);


Data[0] = 0xB1;

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_RES_CONF, Data, 1);


Data[0] = 0x01;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_RES_CONF, Data, 1);

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

Data[0] = 0x01;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

Data[0] = 0x01;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

Data[0] = 0x01;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);


Data[0] = 0x03;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG2, Data, 1);


Data[0] = 0x00;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG2, Data, 1);

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);


Data[0] = 0x03;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG2, Data, 1);


Data[0] = 0xF8;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG2, Data, 1);

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LPS22HB_TempPreEnable(void)

{

uint8_t Data[10];

Data[0] = 0x0A;

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

Data[0] = 0x33;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);


Data[0] = 0x0A;

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);


Data[0] = 0x33;

SPI2_1Wire_Write(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

SPI2_1Wire_Read(CS_LPS22HB, LPS22HB_CTRL_REG1, Data, 1);

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LPS22HB_Press(uint8_t *pRawdata, float *fPress)

{

int32_t RawPresse, Pout;

  uint32_t Temp = 0;

  uint8_t PressLoop;


  for(PressLoop = 0; PressLoop < 3; PressLoop++){

    Temp |= (((uint32_t)pRawdata[PressLoop]) << (8 * PressLoop));

}


  /* convert the 2's complement 24 bit to 2's complement 32 bit */

  if(Temp & 0x00800000){

    Temp |= 0xFF000000;

}


  RawPresse = ((int32_t)Temp);

Pout = (RawPresse * 100) / 4096;

*fPress = ( float )Pout / 100.0f;

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LPS22HB_Temperature(uint8_t *pRawdata, float *fTemperature)

{

short int TemperatureTemp = 0, Tout = 0;

TemperatureTemp = (((uint16_t)pRawdata[1]) << 8) + (uint16_t)pRawdata[0];

Tout = (TemperatureTemp * 10) / 100;

*fTemperature = (float)Tout / 10.0f;

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LPS22HB_RawData(uint8_t *pAddr, uint8_t *pRawData, uint8_t chLen)

{

uint8_t SpiLoop;

for(SpiLoop = 0; SpiLoop < chLen; SpiLoop++){

// UART1_printf("%02X, %02X, %02X \r\n", CS_LPS22HB, pAddr[SpiLoop], pRawData[SpiLoop]);

SPI2_1Wire_Read(CS_LPS22HB, pAddr[SpiLoop], &pRawData[SpiLoop], 1 );

}

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : None

* Description   : 

*******************************************************************************/

void LPS22HB_TempPressGet(float *fPress, float *ftemperature)

{

uint8_t Addr_Temperature[2] = {0x2B, 0x2C};

uint8_t Addr_Pressure[3] = {0x28, 0x29, 0x2A};

  uint8_t data[3] = {0x4F, 0xFF, 0x00};

LPS22HB_RawData(Addr_Temperature, data, 2);

LPS22HB_Temperature(data, ftemperature);


LPS22HB_RawData(Addr_Pressure, data, 3);

LPS22HB_Press(data, fPress);

}


/*******************************************************************************

* Function Name : 

* Parameters    : None

* Return        : 

* Description   : 

*******************************************************************************/

void MeasurementSensorData(const uint8_t ConvertType,ACCGyroAxis_TypeDef *pACCAxis, ACCGyroAxis_TypeDef *pGyroAxis, MagnetAxis_TypeDef *pMagnetAxis, float *pfPress, float *pftemperature, float *pfBatt, uint16_t *pBatt_Percent)

{

int32_t Tmp;


ACCGyroAxis_TypeDef ACCAxis, GyroAxis;

MagnetAxis_TypeDef MagnetAxis;

float fPress, ftemperature;


/* Measurement */

LSM6DSL_ACCGyroGet(&ACCAxis, &GyroAxis);

LIS2MDL_MagnetGet(&MagnetAxis);

LPS22HB_TempPressGet(pfPress, pftemperature);

*pfBatt = Calculation_VBAT(uhADCxConvertedValue[0], 0);

*pBatt_Percent = Calculation_VBAT_Percent(*pfBatt, MINVOLTAGE, MAXVOLTAGE, TARGETPERCENT);

pMagnetAxis->Mag_X = (int32_t) MagnetAxis.Mag_X;

pMagnetAxis->Mag_Y = (int32_t) MagnetAxis.Mag_Y;

pMagnetAxis->Mag_Z = (int32_t) MagnetAxis.Mag_Z;


if(ConvertType == 1){

Tmp = pACCAxis->ACCGyro_X;

pACCAxis->ACCGyro_X = pACCAxis->ACCGyro_Y;

pACCAxis->ACCGyro_Y = -Tmp;


Tmp = pGyroAxis->ACCGyro_X;

pGyroAxis->ACCGyro_X = pGyroAxis->ACCGyro_Y;

pGyroAxis->ACCGyro_Y = -Tmp;


Tmp = pMagnetAxis->Mag_X;

pMagnetAxis->Mag_X = pMagnetAxis->Mag_Y;

pMagnetAxis->Mag_Y = -Tmp;

}

else if (ConvertType == 2){

}

else if (ConvertType == 3){

pACCAxis->ACCGyro_X = -ACCAxis.ACCGyro_Y;

pACCAxis->ACCGyro_Y = ACCAxis.ACCGyro_X;

pACCAxis->ACCGyro_Z = ACCAxis.ACCGyro_Z;


pGyroAxis->ACCGyro_X = -GyroAxis.ACCGyro_Y; 

pGyroAxis->ACCGyro_Y = GyroAxis.ACCGyro_X;

pGyroAxis->ACCGyro_Z = GyroAxis.ACCGyro_Z;


pMagnetAxis->Mag_X = -MagnetAxis.Mag_Y;

pMagnetAxis->Mag_Y = MagnetAxis.Mag_X;

}

else if (ConvertType == 4){

pACCAxis->ACCGyro_X = -ACCAxis.ACCGyro_X; 

pACCAxis->ACCGyro_Y = -ACCAxis.ACCGyro_Y;


pGyroAxis->ACCGyro_X = -GyroAxis.ACCGyro_X;            

pGyroAxis->ACCGyro_Y = -GyroAxis.ACCGyro_Y;


pMagnetAxis->Mag_X = -MagnetAxis.Mag_X;

pMagnetAxis->Mag_Y = -MagnetAxis.Mag_Y;

}

else if (ConvertType == 5){

pACCAxis->ACCGyro_X = ACCAxis.ACCGyro_X; 

pACCAxis->ACCGyro_Y = ACCAxis.ACCGyro_Y;

pACCAxis->ACCGyro_Z = ACCAxis.ACCGyro_Z;


pGyroAxis->ACCGyro_X = GyroAxis.ACCGyro_X;            

pGyroAxis->ACCGyro_Y = GyroAxis.ACCGyro_Y;

pGyroAxis->ACCGyro_Z = GyroAxis.ACCGyro_Z;

}

}




'초보의 아웅다웅 설계하기 > STM32' 카테고리의 다른 글

Keil 자동완성 기능 끄기  (0) 2019.03.21
PID 제어  (0) 2019.03.02
LSM6DSL, LIS2MDL, LPS22HB  (0) 2019.03.01
Base Timer 인터럽트 사용 안하고 설정하기  (1) 2018.12.20
STM32F Sleep Mode에서 Uart로 Wakeup하기  (0) 2018.12.06
SoftUart Only TX  (2) 2018.10.22
Posted by 초보 HW 엔지니어 로망와니

댓글을 달아 주세요